Ameriphone VCO Manual do Utilizador

®VCODIALOGUEVCOOperating Instructions Hearing Loss Help Company(508) 755 1120 VOICE 530 7069997Fax email: hearingLossHelpCo@Hear

Special FeaturesProgramming the Relay Service Number1. Lift handset and press PROG button.2. Enter the phone number on the keypad.3. Push RELAY b

Programming Emergency Calling Message/Your Home Phone Number and Long Distance CarrierTo Program:1. Lift handset and press PROG button and then

memory buttons shown in Figure 24.Each button can be programmed (orreprogrammed using the same proce-dure) for a phone number up to 15digits long.To P

3. Press a memory button (Figure 24)to store this number on that button.4. Immediately hang up the handset.Note: Any number previously stored at that

called Voice-To-Voice Relay or VTV.Contact your local relay service for moreinformation. The relay services vary fromstate to state, and the procedur

3. When connected, read incomingmessages on display and start speaking when "GA" appears.Say "go ahead" when you're done a

2. Dial the number you're calling on the keypad (if you make a mistake,press PROG to go back one spaceto erase the incorrect number), fol-lowed b

4. The phone sends and displays thismessage on the screen; “I AM AVCO USER, PLS CALL (number stored in memory button selected),GA”. You don’t need t

To type a TTY message, use the keys of thekeypad and their corresponding letters(i.e. number 2 is also for letters A, B, andC). On the screen, watch

To Playback Recorded Messages:1. The screen will indicate the number of messages you have received.2. Press 1 to read your messages.Or press 1 again

When using your telephone equipment, always followbasic safety precautions to reduce the risk of fire, electricshock, and injury to persons, including

Direct Audio OutputThe AUDIO OUTPUT socket allowsyou to connect the Dialogue VCO to ahearing aid, neck loop, cochlear implantor other assistive listen

Connecting to the Q-90 PrinterThe Dialogue VCO can be used withthe Q-90 Printer from Ameriphone.Attach the Q-90 Printer cable to theconnector on the b

20SYMPTOMScreen remains blankNo dial toneLetters do not appear when pressingkeypadNo number dialed when memory buttonpressedNothing happens when RELAY

The DIALOGUE VCO has been registeredwith the Federal Communications Commission(FCC) and complies with the standards in Part68 of the FCC Rules. FCC co

22Warrantythe above exclusions or limitations may notapply to you.To get warranty service for your DIALOGUEVCO, you must provide proof of the pur-chas

SpecificationsMaximum gainHigh frequency (3 kHz): 30 dBWide band (300 to 3000 Hz): 20 dBTone control rangeFull range: 300 to 3000Hz using oneslide con

Connecting for Desk or Wall MountDesktop Use ...4Wall Mount ...5Direct Audio Output ...1

Introducing the Dialogue VCO ...2Warranty Ser

Introducing theDialogue VCOThank you for selecting the amplifiedtelephone Dialogue VCO fromAmeriphone. These OperatingInstructions and the associated

Features on theDialogue VCORINGER volume switch AUDIO OUTPUT jackA/C adapter and phoneline connectionTONE/PULSE switchRELAY buttonRELAY MESSAGE button

Setting up Your Dialogue VCOThere are three steps involved in set-ting up your Dialogue VCO.• Insert four AA rechargeable NiCad batteries for back-up

Setting up Your Dialogue VCO (continued)3. Lift the handset and listen for a dial tone.The phone is ready to use.Wall Mount:1. Pull the handset hook o

Using Your Dialogue VCOfrequency you need to boost. To iden-tify the sound frequency range thatbest suits your needs, follow thesesteps:1. When you he

Using Your Dialogue VCO(Continued)HoldTo put the line on hold, press theHOLD button and return the handsetto its cradle. In telephone mode, thescreen